The Crown® 180MA, 280MA and 1160MA are high-value mixer-amplifiers for commercial
and industrial audio. They provide 4-ohm and constant-voltage outputs (70V and 100V).
Some applications include schools, hospitals,factories, restaurant/retail, houses of worship,fi tness facilities, A/V boardrooms, prisons, and small offi ces. Typical uses are paging, background music, security and evacuation instructions.
The mixer-amps vary in their number of inputs,number of outputs, and power range:
• 180MA has 4 inputs and one 80W power amplifier for single-zone systems.
• 280MA has 8 inputs and dual 80W power amplifiers for two-zone systems.
• 1160MA has 4 inputs and one 160W power amplifier for single-zone systems.
Input routing allows each input to be assigned to any output. This drastically reduces the need for additional mixers or amplifi ers (or both) when
systems require either more inputs or outputs. However, each mixer-amplifi er can be upgraded as a facility expands. For example, you can add more
mixers for more inputs, or add more power amps to handle more zones.
Other features include priority muting, phantom power, and capability for remote volume control.
Specifications
Performance
Frequency Reponse (at 1 watt from 4-ohm tap): 70 Hz to 19 kHz ± 1 dB.
Frequency Response (at line out): 20 Hz to 20 kHz ± 1 dB.
Power Bandwidth (at 4-ohm tap, 2 dB below maxium 1 kHz power): 50 Hz to 20 kHz with
< 0.5% THD
Signal to Noise Ratio (ref. to rated power, master volume at minimum): 85 dB.
DC Output Offset: < ±5 mV.
THD: Less than 0.5% at rated power at 1 kHz.
Input Sensitivity (for full output at maximum gain):
Balanced mic inputs: 3 mV.
Balanced line inputs: 800 mV.
RCA connectors: 400 mV.
Input Impedance (nominal):
Mic: 400 ohms.
Line: 100 kilohms.
RCA: 50 kilohms.
Crosstalk: –70dB at 1kHz.
Line Output Level (nominal): 1V into 10 kilohms.
Phantom Power: 15 VDC.
AC Line Voltages Available:
100V 50/60 Hz
120V 60 Hz
220V 50/60 Hz
230V 50/60 Hz
240V 50/60 Hz
Operating Temperature/Humidy: 0° C to 40° C at 95% relative humidity(non-condensing).
Storage Temperature: –20° C to 85° C.
Front Panel Controls and Indicators
Power Switch: Pushbutton on-off switch. The
power switch does not affect the 24V DC auxiliary power input.
Input Volume Controls: Microphone/line, four in
180MA and 1160MA, eight in 280MA. Detented potentiometers with knobs.
Tone Controls: Bass and Treble non-detented recessed potentiometers on each input channel.
Bass ±10 dB at 100 Hz, Treble ±10 dB at 10 kHz.
Power Indicator: Blue LED indicates power on.
Input Signal Presence Indicator: Green LED, one for each input channel, illuminates when input signal exceeds –24 dBu (line) or –70 dBu (mic).
Output Signal Presence Indicator: Green LED,one for each output channel, illuminates when output signal level exceeds 100 mV (45 dB below
full power) from the 4-ohm tap. Does not respond to signals from the AMP INPUT connector.
C O M M E R C I A L A U D I O S E R I E S
• 4 or 8 inputs, 1 or 2 amplifi er output channels
• Ideal for commercial and industrial use
• Balanced Phoenix-type mic/line inputs;
touch-proof screw-terminal speaker outputs
• Any input can be sent to any output
• Priority muting
• Independent bass and treble controls for
each input
• Three-Year, No-Fault, Fully Transferable
Warranty completely protects your investment
and guarantees its specifications
Features
1 kHz Power 80W
Minimum guaranteed power
into 4 ohms or 70V/100V output 180MA
*1 kHz Power: refers to maximum power in watts at 1 kHz with 0.5% THD. *1 kHz Power 80W
Minimum guaranteed power per channel into 4 ohms or 70V/100V output 280MA
*1 kHz Power: refers to maximum power in watts at 1 kHz with 0.5% THD.
*1 kHz Power 160W
Minimum guaranteed power
into 4 ohms or 70V/100V output 1160MA *1 kHz Power: refers to maximum power in watts at 1 kHz with 0.5% THD.
Clip Indicators: Red LED, one per output channel. Illuminates at threshold of audible distortion. Does not respond to signals from the AMP INPUT
connector. Output Volume Controls: One per output channel.
Detented potentiometer with knob. Back Panel Controls and Connectors
Reset Switch: Resets the circuit breaker that protects the power supply. 220/230/240V units have a fuse instead. AC Power Inlet: Detachable IEC.
Auxiliary Power Input: 2-position terminal strip for 24 VDC (±10%) backup power. Accepts up to 14 AWG terminal forks.
Amplifi er Outputs Connectors: One per channel, 4-position terminal strip with COM (Common), 4 ohms, 70V and 100V terminals. Accepts up to 14 AWG terminal forks. Non-touch cover included.
Output VCA Connector: 4-pin Phoenix-type connector for two VCA control lines of +10 VDC and ground. Compatible with Crown 1-VCAP and 4-VCAP modules.
Amp Confi g Switch: A DIP switch with two functions:
1. Assigns an input as the priority input for each output, thereby temporarily muting the remaining inputs. Muting is activated by contact closure.
2. Global enable switch for phantom power. Does not affect RCA inputs. Default position is off. Priority Connector: 3-pin Phoenix-type connector
allows Input 1 or Input 5 (280MA only) to mute other input signals by contact closure. Input Routing Switch (280MA only): DIP switches that assign each input signal to each output. Two switches per input. Line Out Connector: One 3-pin balanced Phoenixtype connector per output channel. Post master, pre-VCA. Level controlled by master volume control.
Input Connectors:
Mic/Line Connector: 3-pin Phoenix-type, balanced, one per input channel.
Dual RCA Input Connector: For stereo music signals, unbalanced, summed together, two connectors per input channel.
Amp Input Connector: 3-pin Phoenix-type, high impedance balanced, one per amplifer channel.
Used to link an additional mixer to the mixer amplifier. Can be used to connect an external processor.
Mic/line Switch: Selects mic-level or line-level signals. One switch for each balanced input.
Link In/Out Switch: Slide switch, one per channel.
With the Link Switch IN, any signal applied to the Amp Input connector will be mixed with the input
signal(s). With the Link Switch OUT, only the signal from the Amp Input Connector will appear at the amplifier output.
Cooling
Convection cooled.
Protection
Current Limit Protection: Included.
Thermal Limit Protection: Over-temperature thermal cutout.
DC-Fault Load Protection: Included.
Included Accessories Power cord, Detachable rack ears, Screws for rack ears
Non-touch cover for output connectors, Phoenix-type connectors, Spade lugs
Optional Accessories
1-VCAP remote volume control for one channel.
4-VCAP remote volume control for four channels.
Dimensions
EIA Standard 19-inch (48.3-cm) rack mount width
(EIA RS-310-B) with rack ears, 3.5-inch (8.9-cm)
height and 12.2-inch (31.0-cm) depth behind the
mounting surface (not including non-touch cover).
4.1 inches (10.5 cm) high including feet. 13.9
inches (35.2 cm) deep from front of knobs to back
of non-touch cover.
Net Weight:
180MA: 21.0 lbs. (9.5 kg).
280MA: 25.3 lbs. (11.5 kg)
1160MA: 25.3 lbs. (11.5 kg)
Shipping Weight:
180MA: 26.0 lbs. (11.8 kg)
280MA: 30.3 lbs. (13.8 kg)
1160MA: 30.3 lbs. (13.8 kg)